Hotpoint HHM5SMWW - Manuel d'utilisation - Page 2

Hotpoint HHM5SMWW
Page 1 Manuel original complet
1 Page 1 2 Page 2 3 Page 3 4 Page 4 5 Page 5 6 Page 6 7 Page 7 8 Page 8 9 Page 9 10 Page 10 11 Page 11 12 Page 12 13 Page 13 14 Page 14 15 Page 15 16 Page 16 17 Page 17 18 Page 18 19 Page 19 20 Page 20 21 Page 21 22 Page 22 23 Page 23 24 Page 24 25 Page 25
Page: / 25
Page précédentePage suivante
Téléchargement du manuel

49-60816-1

INST

ALLA

TION

Preparing of Installation

Read these instructions completely and carefully.

Freezer Location

<RXUIUHH]HUVKRXOGEHFRQYHQLHQWO\ORFDWHGIRU

day-to-day use in a dry, well-ventilated room.

'RQRWLQVWDOOWKHIUHH]HUZKHUHWKHWHPSHUDWXUHZLOOJR
EHORZƒ)ƒ&RUDERYHƒ)ƒ&EHFDXVHLWZLOO

not maintain proper temperatures.

'RQRWLQVWDOOWKHIUHH]HULQDORFDWLRQH[SRVHGWRUDLQ

water or direct sunlight.

Be sure to install your freezer on a floor strong enough
to support it when it is fully loaded.

Level Freezer

Level the freezer from side to side and front to back

VRWKDWWKHOLGZLOOVHDOSURSHUO\8VHVKLPVWROHYHOWKH

freezer if necessary.

NOTE:

It should not be necessary to remove the lid

during installation. If, for some reason, the hinges need
adjustment, see instructions below.

Clearances and Ventilation

$OORZDWOHDVW´PPFOHDUDQFHRQERWKVLGHVRI
WKHIUHH]HUDQG´PPEHWZHHQWKHEDFNRIWKH

freezer and the wall. Leave room above the freezer to
open the lid.

.HHSIODPPDEOHPDWHULDOVDQGYDSRUVVXFKDVJDVROLQH

away from freezer.

'RQRWFRYHUWKHIUHH]HUZLWKLWHPVVXFKDVEODQNHWV

sheets, tablecloths, etc. This reduces air circulation.

Lid Removal

CAUTION

LIFTING HAZARD

7KHOLGLVKHDY\8VHERWKKDQGVWRVHFXUHWKHOLGEHIRUH

lifting.

CAUTION

HINGE SPRING UNDER TENSION

If it is necessary to remove the lid, follow these steps:

1. Remove each upper hinge cover by grasping on the

sides and pulling upwards. Remove each lower hinge
cover by grasping on the sides and pulling down.

2. Open the lid to the maximum position. (The hinges are

loosest at this position.)

3. Loosen, do not remove, the 4 screws from the lower

part of the hinge that are mounted to the cabinet.

4. Raise/lift the lid until the screws align with the larger

slotted openings in the bottom of the hinge. Each
hinge is still attached to the lid with 4 screws.

5. To reinstall lid follow steps in reverse. Tighten all

hinge screws but avoid over-tightening to prevent
stripping. Reinstall hinge covers.

8SSHU+LQJH

Cover

Lower Hinge
Cover

Hinge screws to
be loosened

Hinge screws
to be loosened

Page précédentePage suivante

„Téléchargement du manuel“ signifie que vous devez attendre que le fichier soit complètement chargé avant de pouvoir le lire en ligne. Certains manuels sont très volumineux, et le temps de chargement dépend de la vitesse de votre connexion Internet.

Autres modèles de congélateurs Hotpoint