Oregon Scientific RRA320P - Notice

LED Clock with Projection &

Analogue AM/FM Radio

Model: RRA320P

USER MANUAL

EN

OVERVIEW

FRONT VIEW (FIG. 1)

1
2

3

4
5
6

1. AM / PM
2. Clock
3. Radio ON
4. Sleep mode ON
5. Alarm 1 / 2 ON
6. Low Battery indicator

BACK VIEW (FIG. 2)

１

２

3

5

4

6

7

8

9

10

11

1.

FOCUS

Wheel: Adjust Projection Focus

2.

RADIO

: Turn radio On / Off, Select AM / FM

3.

ALARM 1

and

2

: Select alarm type, BEEP / OFF /

RADIO

4.

+ / -

: Increase / decrease values of the selected

setting

5.

/

SET

/

, : Change settings /

display / View respective alarm status; set alarm

6.

DIMMER

: Select display brightness LO / HI

7.

PROJECTION ON

: Enable / disable continuous

projection

8.

180° ROTATION

: flip image180°

9.

RESET

: Reset unit to default settings

10. AC / DC Socket
11. Battery compartment

TOP VIEW (FIG. 3)

1

2

3

1.

VOL

: Mute / adjust radio volume

2.

SNOOZE / SLEEP

: silence alarm for 8 minutes

3.

TUNE

: Select radio frequency

GETTING STARTED

INSERT BATTERIES

1. Plug AC / DC adaptor into socket.

Memory backup:

2. Remove the battery compartment cover.
3. Insert the batteries, matching the polarities (FIG. 2).

SET CLOCK

1. Press

.

2. Press

+

or

-

to change the settings.

3. The settings order is: 12/24 hr format, hour, minute.

ALARM

To set the alarm:

1. Press and hold desired

SET

/

.

2. Press

+

/

-

to set hour / minute.

3. Press

(or 10 seconds of inaction) to return

display to clock mode.

To activate / deactivate alarm:

Slide to:

•

OFF

– disable alarm

•

BEEP

- beep alarm

•

RADIO

– Radio alarm

To silence the alarm:

• Press

SNOOZE / SLEEP

to silence it for 8 minutes

OR

• Press

,

SET

/

,

+ / -

to turn the

alarm off and activate it again after 24 hours.

RADIO

To activate / deactivate radio:

1. Slide

RADIO ON/OFF

to turn on the radio.

2. Slide

AM / FM

to select.

3. Turn

TUNE

rotary dial to select frequency

To adjust volume:

• Turn

VOL

rotary dial to mute / adjust volume.

To activate sleep timer:

•

Press

SNOOZE / SLEEP

to enter sleep mode.

• Press

SNOOZE / SLEEP

to change the sleep time.

setting (120, 90, 60, 30, 15, 0 min).

PROJECTION

This unit projects time information for your convenience.

For continuous projection:

• Slide

PROJECTION

switch when adaptor is

connected, to enable / disable.

To flip projected image by 180°:

• Press 180° Flip.

To focus image:

• Turn

FOCUS

wheel.

NOTE

If projection is illuminated, do not look directly into

the projector.

RESET

Press

RESET

to return to the default settings.

PRECAUTIONS

• Do not subject the unit to excessive force, shock, dust,

temperature or humidity.

• Do not cover the ventilation holes with any items such

as newspapers, curtains etc.

• Do not immerse the unit in water. If you spill liquid over

it, dry it immediately with a soft, lint-free cloth.

• Do not clean the unit with abrasive or corrosive materials.
• Do not tamper with the unit ’s internal components. This

invalidates the warranty.

•

Only use fresh batteries. Do not mix new and old
batteries.

• Images shown in this manual may differ from the actual

display.

• When disposing of this product, ensure it is collected

separately for special treatment

.

• Placement of this product on certain types of wood

may result in damage to its finish for which Oregon
Scientific will not be responsible. Consult the furniture
manufacturer’s care instructions for information.

•

The contents of this manual may not be reproduced
without the permission of the manufacturer.

• Do not dispose old batteries as unsorted municipal

waste. Collection of such waste separately for special
treatment is necessary.

• Please note that some units are equipped with a

battery safety strip. Remove the strip from the battery
compartment before first use.

NOTE

The technical specifications for this product and the

contents of the user manual are subject to change without
notice.

SPECIFICATIONS

TYPE

DESCRIPTION

MAIN UNIT

L x W x H

183 x 67 x 81mm
(72 x 26.4 x 31.9in)

Weight

386 g (13.6 oz)
without battery

Power

6 V AC adaptor
2 x UM-4 (AAA)
1.5 V batteries

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientific.com) to learn more
about Oregon Scientific products.
If you’re in the US and would like to contact our Customer
Care department directly, please visit:
www2.oregonscientific.com/service/support.asp
OR
Call 1-800-853-8883.
For international inquiries, please visit:
www2.oregonscientific.com/about/international.asp.

EU-DECLARATION OF CONFORMITY

Hereby, Oregon Scientific, declares that this LED Clock with
Projection & Analogue AM/FM Radio (Model: RRA320P) is in
compliance with EMC directive 89/336/CE.
A copy of the signed and dated Declaration of Conformity
is available on request via our Oregon Scientific Customer
Service.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This
device may not cause harmful interference, and (2) This
device must accept any interference received, including
interference that may cause undesired operation.

WARNING

Changes or modifications not expressly

approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation.

This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV

technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact for
support or sales. Please call our customer service number
(listed on our website at www.oregonscientific.com), or on
the warranty card for this product) for all inquiries instead.

We

Name:

Oregon Scientific, Inc.

Address:

19861 SW 95th Ave.,Tualatin,

Oregon 97062 USA

Telephone No.:

1-800-853-8883

declare that the product

Product No.:

RRA320P

Product Name:

LED Clock with Projection &

Analogue AM/FM Radio

Manufacturer:

IDT Technology Limited

Address:

Block C, 9/F, Kaiser Estate,

Phase 1,41 Man Yue St., Hung

Hom, Kowloon,

Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: 1) This device may
not cause harmful interference. 2) This device must accept
any interference received, including interference that may
cause undesired operation.

Horloge de projection LED avec

Radio AM / FM analogique

Modèle : RRA320P

MANUEL DE L’UTILISATEUR

FR

VUE D’ENSEMBLE

FACE AVANT (FIG.1)

1
2

3

4
5
6

1. AM / PM
2. Horloge
3. Radio activée
4. Mode sleep activé
5. Alarme 1/2 activée
6. Indicateur de faiblesse des piles

FACE ARRIERE ( FIG. 2)

１

２

3

5

4

6

7

8

9

10

11

1.

Molette FOCUS

: ajuste la mise au point de la

projection

2.

RADIO:

active / désactive la radio, sélectionne la

bande AM/FM

3.

ALARME 1 et 2 :

sélectionne le type d’alarme, par

BIP, RADIO ou désactivée

4.

+ / - :

Augmente / diminue les valeurs du réglage

sélectionné

5.

/ SET

,

: modifie les réglages /

l’affichage / le statut de l’alarme ; règle l’alarme

6.

DIMMER

: ajuste la clarté de l’affichage HI / LO

7.

PROJECTION ON :

active / désactive la projection

continue

8.

180° ROTATION :

permet de renverser l’image à

180°

9.

RESET

(REINITIALISER) :

réinitialise l’appareil aux

réglages par défaut

10. Prise adaptateur
11. Compartiment des piles

VUE DU HAUT (FIG. 3)

1

2

3

1.

VOL

: muet / ajuste le volume de la radio

2.

SNOOZE / SLEEP

: éteint l’alarme pour 8 minutes

3.

TUNE

: sélectionne la fréquence radio

POUR COMMENCER

MISE EN PLACE DES PILES

1. Branchez l’adaptateur dans la prise.

Protection de la mémoire :

2. Retirez le couvercle du compartiment des piles.
3. Insérez les piles, en respectant les polarités (voir FIG.

2).

RÉGLER L’HORLOGE

1. Appuyez sur

.

2. Appuyez sur

+

ou

–

pour modifier les réglages.

3. Les réglages s’effectuent dans l’ordre suivant : Format

12/24 h, heure, minute.

ALARME

Pour régler l’alarme :

1. Maintenez appuyé SET

ou

.

2. Appuyez sur

+ / -

pour régler l’heure / les minutes.

3. Appuyez sur

(ou ne rien faire pendant 10

secondes) pour revenir à l’affichage du mode horloge.

Pour activer/ désactiver l’alarme :

Placez l’encoche sur :

•

OFF

– pour désactiver l’alarme

•

BEEP

– pour l’alarme par bip

•

RADIO

– pour l’alarme par radio

Pour couper le son de l’alarme :

•

Appuyez sur

SNOOZE / SLEEP

, pour éteindre l’alarme

pendant 8 minutes

OU

•

Appuyez sur

, SET

/

,

+ / -

, pour

éteindre l’alarme et pour qu’elle se déclenche 24
heures plus tard.

RADIO

Pour activer/ désactiver la radio :

1. Positionnez l’encoche

RADIO

sur

ON

pour activer la

radio.

2. Positionnez l’encoche sur

AM / FM

pour sélectionner la

bande désirée.

3. Tournez la molette

TUNE

pour sélectionner la

fréquence.

Pour ajuster le volume :

•

Tournez la molette

VOL

pour mettre le volume sur muet

ou pour l'ajuster.

Pour activer le compteur sleep :

•

Appuyez sur

SNOOZE

/ SLEEP

pour entrer dans le

mode sleep.

•

Appuyez sur

SNOOZE

/ SLEEP

pour modifier le réglage

du temps sleep (120, 90, 60, 45, 30, 15, 0 minutes).

PROJECTION

Cet appareil projette l’heure pour votre commodité.

Projection continue :

•

Positionnez l’encoche

PROJECTION

sur ON une

fois l’adaptateur branché, pour activer / désactiver la
projection continue.

Renverser l’image projetée par 180° :

• Appuyez sur 180° Flip.

Mettre au point l’image :

• Tournez la molette

FOCUS

.

REMARQUE

Si la projection est activée, ne regardez pas

directement dans le projecteur.

REINITIALISATION

Appuyer sur

RESET

pour revenir aux réglages par défaut.

PRECAUTIONS

• Ne pas soumettre le produit à une force excessive, au

choc, à la poussière, aux changements de température
ou à l’humidité.

• Ne pas couvrir les trous de ventilation avec des

journaux, rideaux etc…

• Ne pas immerger le produit dans l’eau. Si vous

renversez du liquide sur l’appareil, séchez-le
immédiatement avec un tissu doux.

• Ne pas nettoyer l’appareil avec des matériaux corrosifs

ou abrasifs.

• Ne pas trafiquer les composants internes. Cela

invalidera votre garantie.

• N’utilisez que des piles neuves. Ne pas mélanger des

piles neuves et usagées.

RRA320P USA MANUAL R1.indd 1

8/29/07 10:16:57 AM