Mode d'emploi pour FSP iFP 2000 Alimentation sans interruption en format pdf, lire en ligne gratuitement. Nous espérons qu'il vous aidera à résoudre les questions que vous vous posez lors de l'utilisation de vos appareils.
Si vous avez encore des questions, posez-les dans les commentaires après les instructions.
"Télécharger le manuel" signifie que vous devez attendre que le fichier soit téléchargé et que vous puissiez le lire en ligne. Certaines instructions sont très volumineuses et le temps qu'elles mettent à s'afficher dépend de votre vitesse d'accès à Internet.
Installation & Operation
Inspection
•
The following item s are inside the box:
●
UPS unit & User m anual
•
Rem ove the UPS from its package and inspect it for dam age that
m ay have occurred during shipping. If any dam age is discovered,
re-pack the unit and retu rn it to the place of purchase.
Connect to Utility Power
•
Connect AC power cord to utility power. Then, the UPS will start
to charge inside battery. For best result, charge the battery for 6
hours prior to initial use.
Plug in Equipment
•
Plug your equipm ent to Battery Backup Outlets on the rear panel
of the UPS.
•
NOTE:
Make sure that the UPS is powered on to protect all
im portant devices from data loss during power failure.
•
C AUTION:
NEVER connect a laser printer or scanner to the
battery backup outlets of U PS. The equipm ent m ay draw
significantly power to overload the UPS.
Turn On/Off the UPS
•
Please transport the UPS system only in the original package t o
protect against shock and im pact.
Rear Panel
400-800VA
1000VA
1500-2000VA
A:
Outlets
B:
AC input
C:
Fuse/Breaker
D:
USB port
E:
Surge protection
LCD Display
Operation Display
UPS
m ode
LCD
Description
UPS
Power
on
W hen UPS is powered on, it
will enter this m ode for 4
seconds.
AC Mode
W hen AVR is functioning,
icon will flash every
second.
LCD inform ation will be
displayed in the following
order when LCD is touched.
1.Output voltage
2.Input voltage
3.Load level
4.Battery capacity
Overload
in AC
m ode
icon will flash.
W hen overload occurs,
alarm will beep every 0.5
second.
Battery
Mode
W hen battery level is low,
icon will flash.
Alarm will beep every 10
seconds and LCD
inform ation will be displayed
in the following order when
LCD is touched.
1.Output voltage
2.Input voltage
3.Load level
4.Battery capacity
Overload
in battery
m ode
icon will flash.
W hen overload occurs,
alarm will beep every 0.5
second.
NOTE: If backlight shuts off, you m ay activate it by to uching the screen.
Fault Code Table:
Fault condition
LCD
Solutions
Output short
circuited
Disconnect short -circuited loads and
restart the UPS again.
Overload fault
Disconnect all output loads and
restart the UPS ag ain.
Overcharge
Call for service imm ediately.
Bad/severely
discharged
battery
Please replace the battery.
High output
voltage fault
Call for service imm ediately.
Over-
tem perature
Call for service imm ediately.
If fault alarm occurs, please call for service imm ediately.
Line-interactive UPS
iFP 400VA~2KVA
FSP Manual Guide
EN
Vous avez encore des questions ?Vous n'avez pas trouvé votre réponse dans le manuel ou vous avez d'autres problèmes ? Posez votre question dans le formulaire ci-dessous en décrivant en détail votre situation afin que d'autres personnes et experts puissent y répondre. Si vous savez comment résoudre le problème d'une autre personne, donnez-lui un indice :)
