CONSUMER SERVICES; Troubleshooting; FIXATION DU CINTRE; FIXATION DE LA BROSSE À TISSU - SteamFast SF-562 - Manuel d'utilisation - Page 9

12 | ENGLISH

CONSUMER SERVICES

For problems with your unit, please refer to the troubleshooting guide located above.

Additional inquiries should be directed to our consumer support services through our website,

www.steamfast.com

. If you do not have internet access, you may also contact our Consumer

Service Department by telephone, at

1-800-711-6617

.

NOTE: In order for our Consumer Service representatives to help you as quickly and

ef

fi

ciently as possible, please have the following information ready before calling:

• Purchase information (where and when you purchased this product)

• Copy of purchase receipt / proof of purchase

• Product serial number (located near electrical speci

fi

cation label on bottom of unit)

For information regarding your 2 year limited warranty, refer to Page 15 of this manual.

Troubleshooting

PROBLEM

POSSIBLE CAUSE

SOLUTION

Unit fails to heat up. When turned,

Steam Dial

DOES NOT

illuminate when set to “ON” posi-

tion.

Unit is not plugged in.

Plug power cord into electrical outlet.

Household circuit breaker / ground

fault interrupter has tripped or

blown a fuse.

Reset circuit breaker / ground fault inter-

rupter, or replace fuse. For assistance,

contact a licensed electrician.

Unit is damaged or otherwise in

need of repair.

Immediately cease usage and unplug. Con-

tact Consumer Service for

assistance (see below for details).

Unit fails to heat up. When turned,

Steam Dial

DOES

illuminate when

set to “ON” position.

NOTE: Always allow suf

fi

cient

time for unit to heat up and begin

producing steam.

No water in unit.

Refer to

Filling With Water

procedure on

Page 8 to

fi

ll unit with water.

Mineral build-up in unit.

Refer to

Mineral Build-Up

section on Page

11 for details.

Unit is damaged or otherwise in

need of repair.

Immediately cease usage and unplug. Con-

tact Consumer Service for assistance (see

below for details).

Excessive gurgling in Hose and

Steam Nozzle / water drips from

Steam Nozzle.

Condensation build-up inside of

Steam Nozzle / Hose.

Some gurgling is a natural effect of the

steaming process. For excessive gurgling

or dripping water, point Steam Nozzle

downward and shake thoroughly to remove

excess water droplets or extend hose

vertically to allow water to drain back into

water reservoir. Condensation build-up inside

hose may cause excess water to escape from

nozzle. To prevent build-up, periodically

straighten hose during use.

Mineral build-up in unit.

Refer to

Mineral Build-Up

section on Page 11 for details.

Steam output is weak or intermit-

tent.

Water level in Water Tank is

running low.

Refer to

Filling With Water

procedure on

Page 8 to re

fi

ll unit with water.

Mineral build-up in unit.

Refer to

Mineral Build-Up

section on Page 11 for details.

FRANÇAIS | 33

FIXATION DU CINTRE

Localisez l'emplacement au bas du cintre. Insérez la section 1 du mât télescopique dans la fente

du cintre.

RACCORDEMENT DU TUYAU DE VAPEUR

Localisez le bas du tuyau, c'est le côté qui n'a pas de buse de vapeur dessus. Vissez le bas

du tuyau dans le support noir sur le dessus de l'unité. Remarque, serrez le tuyau autant que

possible pour éviter les problèmes potentiels.

FIXATION DE LA BROSSE À TISSU

1.

Assurez-vous que le cadran de vapeur est réglé à la position d’arrêt et que l’appareil ne

diffuse pas de vapeur.

MISE EN GARDE : n’essayez pas de

fi

xer la brosse à tissu lorsque l’appareil produit de la

vapeur, car cela peut causer des brûlures et des blessures.

2.

Alignez les anneaux extérieurs de la brosse à tissu sur le bord extérieur de la buse à vapeur.

Enclenchez la brosse à tissu en place.

3.

Pressez fermement la brosse à tissu sur la buse à vapeur jusqu’à ce qu’elle soit bien emboîtée

et fermement en place.